Views: 0 Author: Site Editor Publish Time: 2026-11-11 Origin: Site
AWS A5.28/A5.28M is the American Welding Society specification that prescribes classification requirements for low-alloy steel electrodes and rods used in gas shielded arc welding.
The standard covers solid low-alloy steel electrodes and rods, composite stranded low-alloy steel electrodes and rods, and composite metal cored low-alloy steel electrodes and rods.
The gas shielded welding processes addressed include gas metal arc welding (GMAW), gas tungsten arc welding (GTAW), and plasma arc welding (PAW).
Classification is based on the chemical composition of the electrode for solid electrodes and rods, and on the chemical composition of the weld metal for composite stranded and composite metal cored electrodes and rods.
The as-welded or postweld heat treated mechanical properties of the weld metal are also specified for each classification.
Additional requirements are included for manufacture, sizes, lengths, and packaging.
Optional supplemental designators are provided for lower temperature toughness requirements, diffusible hydrogen limits, reduced Mn + Ni levels in Cr-Mo compositions, and shielding gas ranges.
The current edition is A5.28/A5.28M:2026, which is the sixth edition and revises the 2022 edition.
The specification makes use of both U.S. Customary Units and the International System of Units (SI); since these units are not equivalent, each system must be used independently of the other.
The AWS A5.28 classification system uses the prefix “ER” to denote a filler metal that can serve as both electrode and rod, “E” for an electrode only, and “R” for a rod only.
The two-digit or three-digit tensile strength designator indicates the minimum tensile strength of the deposited weld metal in thousands of pounds per square inch (ksi) for A5.28, or in units of 10 MPa for A5.28M.
The letter following the strength designator indicates the product type: “S” for solid, “C” for composite.
The suffix designator (A1, B2, B3, Ni1, D2, G, etc.) specifies the chemical composition and alloy type.
Optional supplemental designators may follow, including J for low-temperature toughness, HX for diffusible hydrogen limits, and OE for shielding gas oxygen equivalent ranges.
The classifications covered by the specification are enumerated below by category.
Because AWS standards are periodically revised, verify the complete and current list with the latest edition.
ER70S-A1 [ER49S-A1]
ER80S-B2 [ER55S-B2]
ER80S-B2L [ER55S-B2L]
ER90S-B3 [ER62S-B3]
ER90S-B3L [ER62S-B3L]
ER80S-B6 [ER55S-B6]
ER80S-B8 [ER55S-B8]
ER90S-B9 [ER62S-B9]
ER90S-B91 [ER62S-B91]
ER90S-B115 [ER62S-B115]
These classifications designate solid low-alloy steel electrodes and rods with chromium-molybdenum alloy content.
ER70S-A1 contains approximately 0.5% molybdenum and is used for welding low-alloy steels requiring elevated temperature service.
ER80S-B2 contains approximately 1.25% chromium and 0.5% molybdenum, suitable for creep-resisting steels up to 550°C.
ER90S-B3 contains approximately 2.25% chromium and 1% molybdenum, designed for high-temperature service up to 600°C.
ER80S-B6 contains 5% chromium and 0.5% molybdenum.
ER80S-B8 contains 9% chromium and 1% molybdenum.
ER90S-B9 contains 9% chromium, 1% molybdenum, and vanadium-niobium additions for enhanced creep strength.
ER90S-B91 and ER90S-B115 are advanced 9–12% chromium classifications designed for ultra-supercritical boiler applications.
The “L” suffix designates low-carbon versions for improved weldability and toughness.
ER80S-Ni1 [ER55S-Ni1]
ER80S-Ni2 [ER55S-Ni2]
ER80S-Ni3 [ER55S-Ni3]
ER80S-D2 [ER55S-D2]
ER100S-1 [ER69S-1]
ER100S-G [ER69S-G]
ER110S-1 [ER76S-1]
ER110S-G [ER76S-G]
ER120S-G [ER83S-G]
These classifications designate solid low-alloy steel electrodes and rods for nickel steel, manganese-molybdenum steel, and high-strength steel applications.
ER80S-Ni1 contains approximately 1% nickel and is suitable for welding low-alloy steel and weathering steel.
ER80S-Ni2 contains approximately 2.5% nickel, while ER80S-Ni3 contains approximately 3.5% nickel, both offering improved low-temperature toughness.
ER80S-D2 contains approximately 1.75% manganese and 0.5% molybdenum, used for welding manganese-molybdenum steel alloys.
ER100S-1 and ER100S-G are high-strength classifications with minimum tensile strength of 100 ksi, used for welding quenched and tempered steels with yield strengths up to 690 MPa.
ER110S-G and ER120S-G provide even higher strength levels for demanding structural applications.
The “G” suffix indicates a general classification for which the specific chemical composition is not fully specified and is established by agreement between supplier and purchaser.
E70C-A1 [E49C-A1]
E70C-B2L [E49C-B2L]
E80C-B2 [E55C-B2]
E80C-B2L [E55C-B2L]
E90C-B3 [E62C-B3]
E90C-B3L [E62C-B3L]
E80C-B6 [E55C-B6]
E80C-B8 [E55C-B8]
E90C-B9 [E62C-B9]
E80C-Ni1 [E55C-Ni1]
E80C-Ni2 [E55C-Ni2]
E80C-Ni3 [E55C-Ni3]
E80C-D2 [E55C-D2]
E90C-K3 [E62C-K3]
E90C-K14 [E62C-K14]
E100C-K3 [E69C-K3]
E110C-K3 [E76C-K3]
E110C-K4 [E76C-K4]
E110C-G [E76C-G]
E120C-G [E83C-G]
E100C-G [E69C-G]
These classifications designate composite stranded and composite metal cored electrodes for gas shielded arc welding.
The “C” indicates a composite electrode, and the chemical composition designator follows the same alloy naming convention as the solid electrode classifications.
The “K” designations indicate classifications with specific alloy compositions optimized for particular applications.
E90C-K3 contains approximately 1.5% manganese, 0.5% molybdenum, and 0.5% nickel, providing a balance of strength and toughness.
E80C-Ni1 contains approximately 1% nickel and is widely used for welding low-alloy and weathering steels.
The 2022 edition added E90C-K14 [E62C-K14], a high-deposition-rate GMAW wire positioned for large bead applications requiring higher manganese and silicon for deoxidation and flat bead appearance.
Additional composite classifications may exist within these families; verify with the latest edition.
Each element of an AWS A5.28 classification carries specific technical meaning.
The prefix letter indicates the product form and intended application: “ER” denotes a filler metal usable as both electrode and rod, “E” denotes an electrode only, and “R” denotes a rod only.
The strength designator indicates the minimum tensile strength of the deposited weld metal.
For A5.28, the number multiplied by 1,000 psi gives the minimum tensile strength; for A5.28M, the number multiplied by 10 MPa gives the equivalent value in SI units.
The letter following the strength designator indicates the product type: “S” for solid and “C” for composite.
The chemical composition designator that follows indicates the alloy type: A1 for 0.5% molybdenum steel, B2 for 1.25% chromium-0.5% molybdenum steel, B3 for 2.25% chromium-1% molybdenum steel, B6 for 5% chromium steel, B8 for 9% chromium steel, B9 for 9% chromium-vanadium-niobium steel, B91 for 9% chromium-1% molybdenum-vanadium-niobium steel, B115 for 10.5% chromium-0.5% molybdenum-niobium-vanadium steel, D2 for manganese-molybdenum steel, Ni1 through Ni3 for nickel steels, and K3, K4, and K14 for specific high-strength alloy compositions.
The letter “G” indicates a general classification for which the specific chemical composition is not fully specified by the standard and is instead established by agreement between purchaser and supplier.
Optional supplemental designators may be appended: “J” for low-temperature toughness requirements, “HX” for diffusible hydrogen limits (with X specifying the maximum hydrogen level in ml/100g), and “OE” for shielding gas oxygen equivalent ranges.
The 2022 edition also permits a product to be classified simultaneously with “-G” and a specific chemical composition designator, simplifying the re-certification process.
The mechanical property requirements for AWS A5.28 filler metals include minimum tensile strength, minimum yield strength, minimum elongation, and Charpy V-notch impact toughness.
The tensile strength designator in the classification directly correlates to the minimum specified tensile strength.
For ER80S-B2 [ER55S-B2], the minimum tensile strength is 80,000 psi (550 MPa), with a typical minimum yield strength of 470 MPa (68 ksi) and a minimum elongation of 19%.
For ER90S-B3 [ER62S-B3], the minimum tensile strength is 90,000 psi (620 MPa), with a minimum yield strength of 540 MPa (78 ksi) and a minimum elongation of 17%.
For ER110S-G and ER120S-G, the tensile strength ranges are approximately 780–980 MPa and 940–1,140 MPa, respectively, depending on the specific composition and manufacturer.
Impact toughness requirements vary by classification and may be specified at temperatures as low as –50°C when the optional “J” designator is applied.
The precise mechanical property tables are contained within the standard and should be consulted directly for design and qualification purposes.
Verify all mechanical property requirements with the latest edition.
For solid electrodes and rods classified under AWS A5.28, the chemical composition requirements apply directly to the filler metal.
For composite stranded and composite metal cored electrodes, the chemical composition requirements apply to the weld metal produced.
ER80S-B2 [ER55S-B2] specifies carbon at 0.07–0.12%, manganese at 0.40–0.70%, silicon at 0.40–0.70%, chromium at 1.20–1.50%, molybdenum at 0.40–0.65%, and nickel at a maximum of 0.20%.
ER90S-B3 [ER62S-B3] specifies carbon at 0.07–0.12%, manganese at 0.40–0.70%, silicon at 0.40–0.70%, chromium at 2.30–2.70%, molybdenum at 0.90–1.20%, and nickel at a maximum of 0.20%.
ER90S-B91 [ER62S-B91] specifies a more complex composition: carbon at 0.07–0.13%, manganese at ≤1.20%, silicon at 0.15–0.50%, chromium at 8.0–10.5%, molybdenum at 0.85–1.20%, vanadium at 0.15–0.30%, niobium at 0.02–0.10%, and nitrogen at 0.03–0.07%.
For classifications with the “G” suffix, the chemical composition is not specified by the standard and is instead determined by agreement between the supplier and the purchaser.
The precise chemical composition tables are contained within the standard and should be consulted directly for design and qualification purposes.
Verify all compositional requirements with the latest edition of AWS A5.28/A5.28M.
AWS A5.28/A5.28M does not exist in isolation; several companion specifications provide complementary or overlapping coverage for low-alloy steel filler metals.
AWS A5.18/A5.18M is the primary specification for carbon steel electrodes and rods for gas shielded arc welding.
AWS A5.20/A5.20M addresses carbon steel electrodes for flux cored arc welding.
AWS A5.29/A5.29M covers low-alloy steel electrodes for flux cored arc welding, a process-related counterpart to A5.28 for tubular wire applications.
AWS A5.23/A5.23M specifies low-alloy steel electrodes and fluxes for submerged arc welding.
AWS A5.36/A5.36M provides a unified classification system for carbon and low-alloy steel flux cored and metal cored electrodes, incorporating classifications from multiple filler metal specifications.
The ASME Boiler and Pressure Vessel Code, Section II, Part C, adopts AWS A5.28 as SFA-5.28, and the ASME edition includes provisions for conforming material to SFA-5.28 requirements.
Consulting these specifications together provides a comprehensive framework for filler metal selection, qualification, and quality assurance.
The AWS filler metal classification system is organized by welding process and base metal type, with each specification (A5.x) addressing a distinct process or product form.
AWS A5.28 is part of this hierarchical system and addresses low-alloy steel electrodes and rods for gas shielded arc welding.
The “A5” series covers filler metals for arc welding, and the numbering sequence roughly corresponds to the chronological development of the specifications.
The “/A5.28M” suffix indicates that the specification includes both U.S. Customary Units and SI units, a convention applied to AWS standards that have been harmonized with ISO practices.
The 2022 edition introduced several important updates: new optional supplemental designators for shielding gas ranges (OE H/L), diffusible hydrogen (HX), and low-temperature toughness (J); an increase in the manganese upper limit for E80C-Ni1 to 1.75%; the addition of ER90S-B115 [ER62S-B115] and E90C-K14 [E62C-K14]; and the allowance for simultaneous “-G” and specific chemical composition designations.
Users should always confirm that they are working from the most current edition of any AWS specification, as classifications and requirements may be added, revised, or withdrawn between editions.
Verify the current edition number and any superseded designations with the latest edition of AWS A5.28/A5.28M.